A Fire Door Is More Than a Door Leaf: What Actually Has to Work?

Fire Door Safety Week always brings the same message: a fire door only works if every part of it works. That is true, but it only goes so far. The more useful question for anyone managing a building is this: what is this particular door there to protect, and what would stop it doing that job?

Start with the door’s job, not its label

A fire door is a planned gap in a fire-resisting wall, and that wall is there for a reason. It might enclose a protected stair, split a long corridor so smoke cannot fill all of it, separate a flat from the common parts, or shut off a plant room with a higher fire hazard.

That job tells you what matters most. A flat entrance door in a block where residents are told to stay put has to hold back fire and smoke long enough for the common corridor to stay usable. A cross-corridor door in an office does its work mostly by limiting how far smoke spreads along the escape route. A riser door protects a vertical route that fire could otherwise use to jump between floors. The same fault, such as a closer that no longer latches the door, matters far more in some of these places than others.

So when we inspect doors, the first question isn’t “is it certified?” It is “which part of the fire strategy depends on this door?”

The assembly has to work as one

The Fire Industry Association’s Fire Door Safety Week article makes the point well: leaf, frame, seals, glazing, hinges, closer and ironmongery all contribute to how the complete door performs, and each part must be compatible with the evidence behind its fire performance.

In practice, most failures we find come from what happened to the door later:

  • a locksmith fits a different lock or an extra keep and cuts away more of the leaf or frame than the tested design allowed
  • a contractor adds access control, a letterplate or a spyhole without thinking about fire performance
  • a replacement closer can’t reliably shut the door against its latch or seals
  • someone replaces a cracked vision panel with ordinary glass or the wrong beads
  • the frame is sound, but the gap between the frame and the wall was never properly sealed

None is dramatic on its own. Each can undo the protection the door was bought to provide.

Closing is the whole point

A fire door that is open, or that stops a few centimetres short of its latch, protects almost nothing. Self-closing devices are the component we most often find adjusted wrongly, disconnected or wedged. Where doors need to be held open for daily use, suitable automatic release devices can do that legitimately, as long as they let the door close when needed. Government guidance for Responsible Persons lists door release mechanisms among the systems that need inspection or testing.

In England, the Fire Safety (England) Regulations 2022 make this explicit for blocks of flats above 11 metres. The Responsible Person must check fire doors in communal areas at least every three months. They must also use best endeavours to check flat entrance doors at least every 12 months. Both checks must include making sure the self-closing devices work.

The wall around the door matters too

A good doorset in a poor wall achieves very little. Look above the door head, especially where there’s a suspended ceiling. Cable trays, ductwork and pipework often pass through the wall right next to the door. If those openings aren’t fire-stopped, fire and smoke simply go around the door. This is why we treat fire doors as part of the building’s compartmentation rather than as a separate checklist item.

Older doors: judgement, not automatic replacement

The FIA notes that older doors may not have the seals you would expect on a new doorset, and older fire-resisting glass may not carry modern markings. Neither, on its own, proves the door is unsuitable. An earlier FIA mythbuster also warned against condemning existing doors just because they lack certification or labels. Whether a door needs upgrading is a judgement for a competent fire risk assessor, based on its location, the other fire precautions and who uses the building. Damaged or doubtful components still need investigating.

What to ask of your own doors

For each fire door, you should be able to answer three questions:

  1. What is it protecting, and does your fire risk assessment say so?
  2. Does it close fully and latch on its own, every time?
  3. What has been done to it since it was installed, and who checked that work?

If you can’t answer the third question, that is usually the best place to start.

Picture of Jamie Morgan <h5>MIFSM MIFPO MSFPE MIET</h5>

Jamie Morgan

MIFSM MIFPO MSFPE MIET

Jamie Morgan is the founder and Principal Consultant at ESI: Fire Safety. With more than 25 years’ experience across fire safety, electrical engineering and technical compliance, he helps building owners and managers work out what needs attention first and what will work day to day. His work spans fire risk assessments, fire strategies, compliance reviews and DSEAR assessments, backed by hands-on experience designing and implementing life safety systems and electrical safety management.

Growing up around the timber-framed cottages and oast houses of rural Kent gave Jamie a lasting interest in historic and heritage buildings. He brings that interest to his work with churches and listed properties, finding ways to improve fire safety while preserving the features that give them their character.

Jamie holds a Level 6 Diploma in Fire Risk Assessment and a Level 5 qualification in Fire Engineering Design. That combination helps him explain how a building’s design affects fire risk, why a recommendation matters and what it means for the people who use the building. You can check his Intermediate registration on the National Fire Risk Assessors Register.

Jamie keeps up with developments in the profession through his memberships of the Institute of Fire Safety Managers, the Society of Fire Protection Engineers, the Institute of Fire Prevention Officers, the British Fire Services Association and the Institution of Engineering and Technology, which he joined in 2007. He also holds supporter membership of the Institute of Heritage Building Conservation and membership of Society for the Protection of Ancient Buildings.

Tags :

Share :

Facebook
Twitter
LinkedIn
Telegram

Related Articles

Can You Refuse a Fire Safety Inspector Access to Your Premises?

The short answer is no, not in any way that helps you. Fire safety inspectors have legal powers of entry and inspection, and obstructing them or failing to produce records is a separate criminal offence. The more useful question is what an inspection actually asks of you on the day, and how to be ready for it.

Read More »

Speak to a fire safety consultant

Planning a fit-out, need a fire risk assessment or working through a compliance issue?

Bring your plans or questions and we’ll talk through what your project needs.